Asian Journal of Transfusion Science
Home About Journal Editorial Board Search Current Issue Ahead of print Back Issues Instructions Subscribe Login  Users: 1132 Print this page  Email this page Small font sizeDefault font sizeIncrease font size 


 
ILLUSTRATION Table of Contents   
Year : 2013  |  Volume : 7  |  Issue : 1  |  Page : 4-5
Performance qualification: Critical to validation


Department of Transfusion Medicine, Max Super Specialty Hospital, Shalimar Bagh, Delhi, India

Click here for correspondence address and email

Date of Web Publication2-Feb-2013
 

How to cite this article:
Agnihotri A, Kaur S, Kumar J, Chahal R. Performance qualification: Critical to validation. Asian J Transfus Sci 2013;7:4-5

How to cite this URL:
Agnihotri A, Kaur S, Kumar J, Chahal R. Performance qualification: Critical to validation. Asian J Transfus Sci [serial online] 2013 [cited 2021 Oct 23];7:4-5. Available from: https://www.ajts.org/text.asp?2013/7/1/4/106711


Validation is an essential and vital prerequisite for commissioning of equipments. [1] It ensures that the intended process meets the desired outcomes. [2] WHO defines validation as the documented act of proving that any procedure, process, equipment, material, activity or system actually leads to the expected result. Validation of equipments involves completion of three phases: Installation Qualification (IQ), Operational Qualification (OQ), and Performance Qualification (PQ). Compliance to all three phases improves the overall knowledge of the process and assures that the process has been well developed, well maintained, and operates as it should. It reduces the risks involved and expenses of routine processes. [3],[4] Importance of either of these parameters cannot be undermined in day to day operations of blood bank.

We present a case of Refrigerated Blood Component Centrifuge "buckets" which were used for preparation of components. After using the buckets for about 3-4 months it was noticed that the central septum had deviated at its top end, towards the centrifugal force [Figure 1]. The buckets, however, continued to be in regular use as no harm was anticipated.
Figure 1: Centrifuge buckets showing bulge in the median septum and deviation at the top edge

Click here to view


Nearly two months later, a unit of whole blood ruptured in the centrifuge while it was being centrifuged at 3200 rpm for 10 min. When attempts were made to remove the ruptured blood bag from the centrifuge bucket, the technical staff realized that the ruptured bag was entangled in the septum of the centrifuge bucket. The blood bag had to be cut away from the impacted bag in the septum in order to be removed [Figure 2].
Figure 2: Centrifuge bucket showing edges of ruptured blood bag trapped in the septum

Click here to view


Root cause analysis of the event revealed that the medial septum of the all four centrifuge buckets had developed bulges at their lower ends. The top most part of the septum also showed deviation towards the centrifugal force. The heavy centrifugal force lead to a crack at the lower end of the septum and pushed the blood filled blood bag through the crack. The plastic sheet of the blood bag eventually ruptured leading to spillage of a precious unit of whole blood. Failure to correlate the gradual changes in the component buckets to the performance qualification of the equipment lead to the discarding of three potential blood components, which could have been prevented. Although the IQ, OQ, and PQ were performed for the refrigerated centrifuge by evaluating the quality of components, the buckets were not individually assessed for their long-term performance.

This case emphasizes the role of performance qualification (PQ) phase of validation. PQ must be carried out over longer periods of performance for all aspects of procedures, processes, equipments, materials, activity or systems as a whole. It helps test the ability of the process to perform over longer periods of time within tolerance, deemed acceptable.

 
   References Top

1.British Committee for Standards in Haematology, Transfusion Task Force, Allard S, Burgess G, Cuthbertson B, Elliott C, et al. Guidelines for Validation & Qualification, including Change Control, for Hospital Transfusion Laboratories. Transfus Med 2012;22:5-43.   Back to cited text no. 1
    
2.Supplementary guidelines on good manufacturing practices: Validation. In: WHO Expert Committee on Specifications for Pharmaceutical Preparations. 40 th Report. Geneva: World Health Organization; 2006.  Back to cited text no. 2
    
3.World Health Organization. WHO Technical Report Series No. 961; Annex 4. Geneva: WHO; 2011. p. 29-33.  Back to cited text no. 3
    
4.Böcker W, Clark M, Desaint C, Davis R, Distler P, Izaguirre C, et al. ISBT-Guidelines for validation and maintaining the validation state of automated systems in blood banking. Vox Sang 2003;85 Suppl:S1-14.  Back to cited text no. 4
    

Top
Correspondence Address:
Ajju Agnihotri
Blood Bank, Department of Transfusion Medicine, Max Super Specialty Hospital, Shalimar Bagh, New Delhi - 110 088
India
Login to access the Email id

Source of Support: None, Conflict of Interest: None


DOI: 10.4103/0973-6247.106711

Rights and Permissions


    Figures

  [Figure 1], [Figure 2]



 

Top
 
  Search

  
    Similar in PUBMED
   Search Pubmed for
   Search in Google Scholar for
    Email Alert *
    Add to My List *
* Registration required (free)  


    References
    Article Figures

 Article Access Statistics
    Viewed2901    
    Printed156    
    Emailed0    
    PDF Downloaded20    
    Comments [Add]    

Recommend this journal

Association Contact us | Sitemap | Advertise | What's New | Feedback | Copyright and Disclaimer

2006 - Asian Journal of Transfusion Science | Published by Wolters Kluwer - Medknow
Online since 10th November, 2006